# epkowa.conf -- sample configuration for the EPKOWA SANE backend
# Copyright (C) 2004, 2008, 2009 Olaf Meeuwissen
#
# See sane-epkowa(5), sane-usb(5) and sane-scsi(5) for details.
# Detect all devices supported by the backend.
# If you don't have a SCSI device, you can comment out the "scsi"
# keyword. Similarly for the other keywords.
#
usb
scsi
# For any USB scanner not known to the backend (yet), you may, at your
# own peril(!!), force the backend to recognise and use it via libusb.
# You can do so by the following configuration command:
#
# usb <USB vendor ID> <USB product ID>
#
# SEIKO EPSON's USB vendor ID is '0x04b8' (without quotes). In order
# to find the USB product ID, use lsusb(1).
# A sample configuration for the Epson Perfection 1650 (Epson GT-8200),
# which has a product ID of 0x0110, would look as follows:
#
#usb 0x04b8 0x0110
# For SCSI devices not detected, you can add an entry like:
#
# scsi EPSON GT-20000
#
# where the GT-20000 bit corresponds to the SCSI model information as
# shown in the output of dmesg(1) or in the /var/log/kern.log file.
# Network attached devices may be made to work by first installing the
# (non-free) iscan-network-nt package and then adding configuration lines
# as per information below.
#
# For each network attached device, you must add an entry as follows:
#
# net <IP-address|hostname> [port-number]
#
# Ask your network administrator for the device's IP address or check
# for yourself on the panel (if it has one). The port-number is very
# optional and defaults to 1865.
# Note that network attached devices are not queried unless configured
# in this file.
#
# Examples:
#
#net 192.16.136.2 1865
#net 10.0.0.1
#net scanner.mydomain.com
# Some backend behaviour can be customized by using the option keyword
# followed by an option name, as shown below.
#
# option <option-name>
#
# Currently available options:
#
# Makes the automatic document feeder the default document source
#option prefer-adf
# epson.conf
#
# here are some examples for how to configure the EPSON backend
#
# SCSI scanner:
scsi EPSON
# for the GT-6500:
scsi "EPSON SC"
#
# Parallel port scanner:
#pio 0x278
#pio 0x378
#pio 0x3BC
#
# USB scanner:
# There are two different methods of configuring a USB scanner: libusb and the kernel module
# For any system with libusb support (which is pretty much any recent Linux distribution) the
# following line is sufficient. This however assumes that the connected scanner (or to be more
# accurate, it's device ID) is known to the backend.
usb
# For libusb support for unknown scanners use the following command
# usb <product ID> <device ID>
# e.g.:
# usb 0x4b8 0x110
# And for the scanner module, use the following configuration:
#usb /dev/usbscanner0
#usb /dev/usb/scanner0
c'est pô grave
Merci à tous d'avoir essayer
L'imprimante citée plus haut doit pouvoir se connecter en linux 32 et 64
La largeur m'embète un peu . elle devrait rentrer dans le meuble prévu à cet effet
Je reviendrais certainement très vite, linux étant un vaste sujet
amitiés surfantes
rhodes38
Bonjour à tous
Je me permets de ré-ouvrir ce sujet concernant l'impossibilité d'imprimer avec mon EPSON depuis mon passage sur linux.
Pour palier au problème j'imprimais avec mon pc portable en wifi m'évitant ainsi de racheter une autre imprimante. Pas très pratique mais.
Et là cet AM travaillant pour mon club, et sur mon PC fixe j'ai lancé une impression et ô miracle , celà fonctionne.
Celà vient il d'une MAJ effectuée entre-temps ou le retour du soleil en Rhône-Alpes mais inutile de vous dire combien cela me fait plaisir.
amitiés surfantes
rhodes38
oui, il est fort possible qu'une màj ai fait un miracle, comme aussi bien elle peut faire un désastre, c'est l'informagique
le principal est que ça fonctionne
De nouveau mon imprimante me joue des tours. Enfin plus précisément le scanner.
Peut être faut il que j'ouvre un nouveau sujet?
Je voudrais essayer avec Wine. Peux t'on m'expliquer comment procéder si possibilité il y a???
Je fais tourner actuellement un logiciel avec Wine (musique)
Cordialement